These stampable overlay systems typically range in thickness from ¼ inch to 5/8 inch. Self-leveling concrete has been a staple for repair and leveling of damaged or worn concrete. Back to TopThin Section / Microtoppings are thinner versions of their cousins the stampable overlay. Either a powder or liquid release material can be used, depending on the final look and/or color scheme that is desired.With the growth of interior decorative concrete finishes, we can now add concrete to the list of options of floor coverings for your next interior floor project. They range in thickness from 1/32 inch up to 1/8 inch thick.For more relevant information, check out the links below:carpet laying auckland, carpet laying northshore . Like stampable overlays, these systems cure in 24 hours, and are usually ready for foot traffic within 36 hours of application. The type of finish (knock down, orange peel, smooth) all depends on the spray pattern and method of spray application. Most self-levelers can go down 1/4 inch to 1 inch, with the ability to go to a feather edge. These types of materials are usually applied through a hopper gun under pressure. In the last few years contractors have started adding integral color to self-leveling systems, or coming back after 24 hours and using stains, dyes or tints to create colorful floors. It is important to seal microtopping finishes, as they are micro porous and will tend to collect dirt that is difficult to remove once embedded into the material. Once the first coat is dry, adhesive backed stencils are laid out over the floor. These materials cure in 24 hours, and can usually be sealed and light traffic allowed within 36 hours after application. Stampable overlay systems are designed to be applied with a gauge rake, quick trowel smoothed, and then imprinted with the desired texture or stamp tool. The surface needs to have sufficient profile (be rough enough) so that the overlay material can bond both chemically and mechanically. Some typical finishes for Microtopping floor coverings include, but are not limited to smooth trowel, rough trowel, stippled, and orange peel. Self-leveling concrete can be expensive, and does require a higher level of proficiency than the microtopping and spray texture products. Either a clear or colored sealer is then applied for maintenance and aesthetics. Because these materials are so thin and dry very quickly, texture is limited to how the products are applied. A second color or wear coat is spray applied over the stencil, and once dry the stencil is peeled up and discarded. They are easily applied with trowels, squeegees, brushes, and or rollers, all depending on the final look that is desired. Until recently, another solid surface floor covering would be placed on top of the self-leveling material. The common thickness is 3/8 inch, which is usually thick enough to accommodate most standard imprinting tools in the market place. A fist scratch or "grout coat" is applied. If you are looking for a 3-dimensional textured floor covering that resembles most any natural material (stone, tile, wood, etc. While most concrete floor coverings can be used both interior and exterior, for simplicity we will focus on interior flooring, especially since this is where a vast majority of
stainless steel floor drain manufacturers these materials end up being used. Check with the manufacturer of the microtopping system you are using as to what sealers (water or solvent or both) are best suited for that particular application.) consider a stampable overlay on your next project. I always recommend a mechanical grinding or profiling of the floor, as this will always provide better profile versus an acid etch or other means of chemical surface profiling. The single most important factor with any stampable overlay application is surface preparation. They are very similar to Microtopping type finishes in that they are thin, but differ in that they usually contain more sand, and provide a rougher, grittier finish. In recent years we have seen these types of finishes become more popular in high traffic interior spaces because of their durability, low cost, ease of application, and range of patterns and colors. They utilize "beefed up" polymers that allow the material to go down very thin and yet maintain strength, durability and abrasion resistance. Back to TopSpray Applied or Stenciled Concrete floor coverings are not as popular for interior finishes or coverings, but have been around for decades for exterior coverings for pool decks, and patios. This is a very popular finish for residential and small commercial spaces.Textured Concrete Floor Coverings, also known as stampable overlays, are designed for one purpose, and one purpose only to provide a textured surface similar to stone, tile, brick, wood, or other natural material. The advantage of a self-leveling system is that it can correct uneven floors, repair damaged floors, and at the same time provide a very dense smooth and durable concrete floor. Another common microtopping finish involves coming back 24 hours after application and applying concrete stains or dyes to create a stained concrete appearance. Back to TopSelf-Leveling underlayments used as concrete flooring is the newest trend in concrete floor coverings. Some systems
balcony floor drain offer a finish coat, which contains no sand, and is used only when an ultra smooth top or final surface is specified. Most microtopping systems offer a base coat, which contains sand, and is used in the first two applications. Surface preparation, once again, becomes very critical with self-leveling systems
